CHDK Motion Detection

[Kociałko]

no okazało się ,że trochę zbładziłem podając stronę o porcie drukarki post wcześniej
pomyliłem port szeregowy z LPT
szeregowy daje +-12V a LPT 5V
a 5V akurat potrzebujemy
na razie ojciec założyciel GrAnd się przyznał ,że używa drivera giveio.sys i napisał własny program ,który wysyła dane na port drukarki i dzięki temu ustawia na pinach (prawdopodobnie 18 pin GND i 1 lub 2-9) 5V

Fingalo się przyznał ,że używa ".NET program with inpout32.dll" i własnego programu

może bedą wspaniałomyślni i się podzielią

[Kociałko]

dzięki uprzejmości Fingalo mamy teraz do dyspozycji program do wysyłania krótkich definiowanych sygnałów z LPT do USB i naszych Canonków
(5 przycisków,nie zapamiętuje konfiguracji)

jak ktoś ma lutownicę i trochę zacięcia może się pobawić

połączenia:
wtyk LPT pin 25 (masa) do gniazdka USB na pin 4
wtyk LPT pin 2 (+5V) do gniazdka USB na pin 1

obrazek poglądowy gniazdka USB z przodu tu http://s3users.com/forum/showpost.ph...&postcount=218

program Fingal-a http://hem.passagen.se/fsmmal/CHDK/remote%20utils.zip
(with .net source)
(Copy inpout32.dll to windows/system32) and run the .exe file

osobiście testowałem
i czasami to działa
zdarza mu się wieszać przy zoomie na min lub max
wiesza się mniej jak dochodzimy zoomem krokami używając przycisku StopZ (stop zooming)

być może wersja GrAnda jest stabilniejsza ,może czasy trzeba dobrać lepiej -jeszcze nie wiem

niekórzy szczęśliwcy mogą się cieszyć sterowaniem z kompa programem PSRemote http://www.breezesys.com/PSRemote/features.htm#ps
ale nie rozpoznaje on części modeli (no i nie da się za jego pomocą wykonywać skryptów CHDK )

[Kociałko]

Evavr wydał testową wersję firmware z poszerzona przysłoną F od 9 do 11
http://ewavr.nm.ru/hdk/for_test/

o ile to działa pewnie niedługo Fingalo to doda do swojej wersji

niektórzy na forum chwalą siż zdjęciami z migawką rzędu 1/40 000...i więcej

chłopaki myślą również nad wykrywaniem twarzy....

no niedługo nasz Canonek będzie prał ...gotował i sprzątał

[winiarro]

To super, za kilka dni Fingalo's powinien wypuścić nową wersję
Mam przy okazji pytanie. Czy możliwe byłoby dodanie sterowania balansem bieli w stopniach Kelvina? Niby można to samo zrobić na kompie z RAWem, ale nie zawsze się chcę nad tym siedzieć. Może Kociałko ma jakieś możliwości w tym kierunku?

[Kociałko]

za pomocą komendy "set_prop 5 wartość" da się ponoć ustawić balans bieli
prawdopodobnie jeśli masz powiedzmy 7 definiowanych pozycji balansu bieli to można to przełączać w skrypcie
set_prop 5 1 to da ci ustawienie auto
set_prop 5 2 to da ci ustawienie dzień
set_prop 5 3 to da ci ustawienie pochmurno
set_prop 5 4 to da ci ustawienie światło żarowe
set_prop 5 5 to da ci ustawienie fluorescencyjne
set_prop 5 6 to da ci ustawienie fluorescencyjne H
set_prop 5 7 to da ci ustawienie pod wodą

ale nie testowałem
napisz sobie prosty skrypt i sie pobaw i daj znać co wyszło

"The Digic III camera have different property number assignments (for example, the A570 ISO is at #149, not #21, and the white balance control is #268, not #206"

pisze niby ,że balans bieli czasem jest 206 ,a czasem 268 też -to zależy jaki aparat
w innym miejscu znów
"206 White Balance 0=OFF, 1-11 for various setting"

hmmm no to się pogubiłem lekko
czyli set_prop : albo 5 albo 206 albo 268 najprawdopodobniej

[winiarro]

Napisałem ten skrypt. Co prawda poziom regulacji jest taki sam jak w zwykłym menu, ale są tryby (np. AUTO), w których nie można ustawić balansu bieli. Dzięki temu skryptowi mam taką możliwość. Wartość set_prop rzeczywiście trzeba dobierać odpowiednio do modelu aparatu. Po ustawieniu 206 zmieniał tryby kolorów (odcień skóry, błękit, itp.). Dopiero po ustawieniu na wartość 5 u mnie działa ok.
0 auto
1 dzień
2 pochmurno
3 światło żarowe
4 fluorescencyjne
5 fluorescencyjne H
6 lampa błyskowa
7 ręczny balans (pobierz dane z otoczenia)
8 nie wiem, ale zimne kolory
9 nie wiem, ale ciepłe (czerwone) kolory
10 pod wodą

Te wyniki są z trybu Auto na Canonie A620. Wybrałem ten tryb, bo
ma zablokowane zmiany balansu bieli. Po testach na innych trybach
jest identycznie.

rem Author - winiarro

@title White Balance
@param a Value of WB
@default a 0

print "Starting WB"

rem for each shoot
set_prop 5 a
shoot
print "Finishing"
end

[Kociałko]

Ewavr napisał ,że jego modyfikacja pozwalająca na większą przysłonę działa tylko przy końcówce zoomu-no ale dobre i to
"It seems, that big Av works only on long end of zoom. "
!!! Łączenie podwójnego wpisu !!!
pojawiła sie wersja CHDK która próbuje zebrać wszystkie najlepsze funkcje z różnych wersji

http://malbe.nm.ru/chdk/

wklejam oryginalnego posta z forum - nie mam zacięcia tłumaczyć całość
"As already indicated, the build is a symbiosis versions vitalyb + grand + ewavr + fingalo (advanced syntax scripts) + mx3 (movement detector) + my innovations .

Let's consistently go for the new items on the menu.

"Extra Photo Operations"
In this menu, you can set the parameters for the list of additional photographic operations.

"Override shutter speed value" User-value extracts reinstalled. Together with the following item in the menu -
"Value factor" makes the final shutter speed as the product of
"Value factor" * "Override shutter speed value"
"Value factor" in relation to shutter speed can be chosen from the following set of values: ( "0.00001", "1 / 10000, 1 / 1000, 1 / 100, 1 / 10", "1", "10", "100")
"Override aperture value"
This option allows custom fitting realize value diaphragm number. We offer an opportunity to establish any Av value, from the lowest possible at this chamber, with step 1/3 Ev and maximum shift in 5Ev. This way was chosen to ensure compatibility, as specific values at different aperture camera models may vary. In any case, if this option is set, the information of that fact will be reflected on the display in accordance with the characteristics of the particular camera. I recommend also observe Av value for the list of additional values. Once made a shot, you can actually see the Av value was set (likely). That means, for example, when trying to establish the diaphragm in 13, and, apparently, Canon says 13, but, while we see the list App. values that Av = 11. Yes, and subsequent analysis histogram shows that the 13 somehow not a…
"Override ISO value" - Setting arbitrary values ISO. ISO Makes expand interval, above all, its lower boundary. Lower ISO, at least, are working at a610-a620 and s2. At 630-640 there are arbitrary ISO. On the other chamber situation is not clear
"Value factor," Has the same meaning as above. Range: "1", "10", "100"
"Override subject dist.value" Custom Installation - distance focus
"Value factor (mm) - multiplier for the above values. Has values ( "1", "10", "100", "1000"). All of this is in millimeters.
Call attention to that the facility operates only on the mode of manual focus. There is a view that this way to use manual focus several convenient than through standard slider with incomprehensible behavior
Test results show that for small distances (macro range) and perform substantial shifts for at least 1 cm on the average not less than 5 cm, if you wish, you can make more accurate verification
Installing all of the above parameters is a consequence of the information reflected in the display. In the case of extracts-to focus displays installed (custom) value extracts, and then (after focus) - Made recalculation of the established property case.
Monitoring. If you convert this amount steadily during the shooting, it is possible to draw the attention that, for example, an extract of 1/13, which is displayed on the display Canon standard way is not always the same 1/13. There may be slight variations in the least digits
It should draw attention to that with the installation of custom settings via CHDK, camera does not produce recalculation of the exposition. Therefore, for correction should be given to the importance Overexposure value from the list and compensate for the additional exhibit traditional way. One NO. This value does not take into account the flash light value, ie flash disregards. Plans to implement, given the restatement exposure and establish appropriate shift value

Next submenu:

"Bracketing in continuous mode" is a set bracketing which works in continuous shooting mode.
"Tv bracketing value" -Bracketing on Tv (shutter speed)
Sets shift in the range 1/3 - 2 Ev.
"Av bracketing value" -Bracketing on the diaphragm. Same-value in the 1/3-2 Ev
"ISO bracketing value" -Bracketing of sensitivity in ISO standard. The amount of shift is formed together with the "Value factor"
"Subj.distance bracket.value (MF)," Bracketing focus on the distance. All the same
"Bracketing type" - TYPE of Bracketing. The choice of this set: "+/-", "-","+".
Affects all bracketings. Indicates changes direction. In the second and third case is, respectively, simply reducing shifts and increase in the value of exposure Ev. In particular, "-" leads to a cascade INCREASE of shutter speed and REDUCE value of diaphragm. In the case of ISO focus direction and a distance values change with the direction changes.
+ /-breketing-in the literal sense of the word. The first step is the initial exposure - Second-shift to a negative Ev, in accordance with the above described logic. When reaching a magnitude of the limit with this type of value-bracketing not duplicated. Ie if we present diaphragm 4, it will be the next sequence (approx.): 4, 3.5, 4.5, 3.2, 5, 2.8, 5.5, 6, 7…… ..
It should be noted that bracketings can work with the user through the installation of expo-parameters of CHDK!

As you may have noted, in the root menu, a further item - "Video Parameters" on the thin video settings for control over which we should be thankful distinguished EWAVR!


The next menu is a subsidiary of the menu "OSD parameters:
"Miscellaneous Values" (Additional values)
Through this menu, you can control the display set at the conclusion of additional values, which may be useful in the process of photographing

"Show Zoom" display the list of additional value of the current value Zoom
"Zoom value" - type display Zoom (it was in previous versions)
"Show 'real' Aperture," to show "real" meaning the number of diaphragm (the same was the case in previous versions)
"Show 'real' ISO-show" real "value ISO. Including and automatically
"Show 'market' ISO-show" marketing "value ISO. As a surprisingly there have Canon, apparently this division ISO. But exposition is calculated on the basis of "real". For example, the 620 th the claimed 50 "marketing" around 46 "corresponds to the real." For the 630 th interesting-against 80 "marketing" see 49 "real"
The differences can be substantial. In the case of AutoIso in Exif written AutoIso calculated from marketing. This can be seen through the program "ExifTool"
As a result of observation of iso on my 620-m has reached the following conclusions. In the mode P auto iso never goes higher marketing 100. In fully automatic mode auto iso does not rise above 140. In priority modes auto iso always at least, as in performing at the dial modes (portrait, landscape, night scenery). In some regimes performing auto iso can be raised to 200 (but not above)
"Show ISO only in Autoiso mode" Show-meaning ISO mode only AutoIso
"Show Ev (Tv + Av)" Show-exposed camera exposure value based on the values of shutter speed and diaphragm.
"Show Ev (Bv + Sv)," The right equation exposure (brightness value + sensitivity scenes set in a camera)
"Show Bv (brightness value) int-brightness scenes through recalculation of the parameters established in the camera. Just Av-Sv + Tv.
"Show Bv (brightness value) ext" This value is written in Exif as MeasuredEV
Comment on Phil Harvey (author exifTool):
this the Canon name for what should properly be called MeasuredLV, and is offset by about -5 EV from the calculated LV for most models
"Show Overexp.value (No flash!)" This is the result of subtracting Av-Bv-Sv + Tv. Not accounted Fl- flash light value
There may seem interesting observations
For example, in the theatrical mode, "Beach" Canon uses compensation exposure +1 / 3, and the "snow - + 2 / 3. In the automatic mode overexpo sometime to 1/3 in P- mode while-0. When Bv negative values (or close to negative) ignored underexpo to -1 (that is not available in red expoparams is in the manual modes). Either party that is the policy of "Canon", or something, I'm confused…:-/
"Show Scene Luminance"- run average in standard illumination scenes candelas per square meter… calculated from a ratio to Bv = 12.5. Ie Wages can be used as an exposure meter

Improvements for setting calculator DOF. The menu is a subsidiary of the menu "OSD parameters"
"DOF Calculator"
Show DOF calculator-options - "Don't", "Separate," "In Misc." Proposed either separately display calculator (as in the previous assembly), or withdraw from the list of additional value
"Canon Subj. Dist. as Near Limit"
pilot point. As probably noticed many more meters for distance calculator shows, to put it mildly, inaccurate shooting distance to the object. It remains a mystery what gets us in the largest Canon. One can not say that the meter plus or minus is not important. This is important, in particular, to calculate the power outbreak. Autoiso observed in the flash mode for almost a clear correlation autoiso values of the distance to the object. At a maximum of this value must go somewhere in an area declared flash guide number-4.2 meters. So, if it is considered that Canon gets somewhere around the border zone nearest acceptable sharpness, the guidance accuracy and distance increases and flash guide number is, and docking with the values and burned without Zuma once more or less similar. That is all for my 620 th. And, as far as I understand, for many it is not clear what the connection between the manual focus slider, running his exemplary values, and why when, like, again, everything about "correct" said the object looks like the focus is not.
"Use EXIF Subj. Dist. (PC65)
Also, a pilot point. It should be noted that there is a difference between what we are getting now, as the distance to the object through CHDK and the importance that remains in the canon exif. Perhaps in the EXIF tend to be smaller, but the same line with the above, in the manual mode. This value corresponds to property case 65. Here it is proposed to use this amount for calculation. Combined with the first item, in my view, is produced more accurate results.
In short, you can experiment and come to their conclusions somehow
IMPORTANT. Setting the above parameters directly affect the relevant script-commands establishing distance focus, as well as the behavior of camera in bracketing to subject distance in manual mode and the custom installation distance focus
"Show Subj. Dist. in Misc." Show focus distance from the list of additional values (provided that the above selected "In Misc" show-value calculator depth of field from the list of additional)
"Show Near Limit in Misc." Same, just near the border zone regarding acceptable sharpness
"Show Far Limit in Misc." the same, only distantly border
"Show Hyperfocal Dist. in Misc." - the same, only hyperfocal distance
"Show Depth of Field in Misc." - the same, only the depth of the zone…

Further, the syntax of structure is changed in accordance with fingalo, script-commands are added, the names of some teams brought into line with the meaning of their load (old names - also left for compatibility), changed the engine of some teams, that the installation was through the same Hook , which is used for the custom installation expanded values
The current list of colors:
"<>",
"<=",
">=",
"<"
">"
"not"
"or"
"and"

"let"
"if",
"then"
"else"
"endif"
"for"
"to"
"next"
"step"
"do"
"until"
"while"
"wend"
"goto"
"gosub"
"return"
"call"
"rem"
"cls"
"print_screen"
"print"

"click"
"press"
"release"
"shoot"
"sleep"


"get_av96"
Since Canon uses to calculate the rate of 96 (it is found by analyzing the values match formulas APEX), and also in the token indicates that the installation corresponds to the value of Av * 96. From my point of view, so convenient. Load-meaning teams receive appropriate value in a variable Av * 96 from the relevant again, PropertyCase

"get_bv96" get brightness value

"get_day_second current within one second of the day
"get_dof" get the depth of sharpness in mm
"get_far_limit" get the border zone ranged acceptable sharpness mm
"get_focus"
"get_hyp_dist" get hyperfocal distance
"get_iso_market" get "marketing" ISO
"get_iso_mode" obtain ISO mode (the former get_iso) For example, for 620 th:
0-> Auto "
50-> 50 "
100-> 100,
200-> 200,
400-> 400,
"get_iso_real" get real "value" ISO
"get_iso" obtain ISO mode
"get_near_limit" get dipped border zone acceptable sharpness
"get_prop" obtain property case, call
"get_sv96, receive sensitivity value in the standard Apex. As always, multiplied by 96
"get_tick_count" returns system time
"get_tv96, tv * 96
"get_user_av_id", the former get_av. Get custom installation av (in the manual modes) for ID in CHDK
For example, for 620 th has a set:
(9, 288, "2.8")
(10, 320, "3.2")
(11, 352, "3.5")
(12, 384, "4.0")
(13, 416, "4.5")
(14, 448, "5.0")
(15, 480, "5.6")
(16, 512, "6.3")
(17, 544, "7.1")
(18, 576, "8.0")
The first of values-in ID CHDK. The move to the next ID is, in fact, a shift in the 1/3 ev. The second value is a av * 96

"get_user_av96" returns custom av * 96
"get_user_tv_id" returns CHDK identifier for the established user manual modes tv. For example, in the case of the 620-meters, we have:
(-4, -128, 2.5)
(-3, -96, "2")
(-2, -64, "1.6")
(-1, -32, "1.3")
(0, 0, "1")
(1, 32, "0.8")
(2, 64, "0.6")
(3, 96, "0.5")
(4, 128, "0.4")
This is part of possible values. Meaning load deflection on the id-the same as in the case of av
"get_user_tv96" returns installed in the user manual modes importance tv * 96
"get_vbatt", the voltage of the battery
"get_zoom"
"set_av96_direct" direct installation av * 96. It works similar to direct the installation of the interface chdk av. In any mode
"set_av_rel" see "set_user_av_by_id_rel (compatibility)
"set_av96", the installation av * 96 in accordance with acceptable canon list for the camera. Works in any mode
"set_av" see "set_user_av_by_id (compatibility)
"set_focus"
"set_iso_mode", the installation of a regime ISO.
"set_iso_real" Direct installation ISO. It works similar to the installation of the ISO interface CHDK
"set_iso" see "set_iso_mode (compatibility)
"set_led - numlock lamp. Transmitted three-parameter ID indicator state, the brightness
"set_prop", the installation, call propertycase
"set_raw_nr", the installation script regime in noise reduction / / "Auto", "Off", "On" (0,1,2)
"set_raw", the installation script in raw mode and disables the last
"set_sv96" direct installation of the sensitivity of APEX (Sv * 96)
"set_tv96_direct" direct tv installation * 96. Works installation excerpts from the same interface CHDK
"set_tv_rel" see "set_user_tv_rel_by_id (interoperability)
"set_tv96" direct tv installation * 96 from a list of valid values CANON (this value type N * 32. N for the 620 th can have values from -12 to 32. works installing excerpts from the same interface CHDK

"set_tv" see "set_user_tv_by_id (interoperability)
"set_user_av_by_id_rel" av installation on the current user on bias. The offset indicated in Id. Id rationale was listed above
"set_user_av_by_id" Custom Installation av according to the Id in CHDK. The point above id-
"set_user_av96" custom installation av * 96 in the manual modes
"set_user_tv_rel_by_id" custom installation on the current tv on bias. The offset indicated in Id. Id rationale was listed above
"set_user_tv_by_id", the installation of custom tv permissible, in accordance with canon ID for CHDK
"set_user_tv96", the installation of custom Tv * 96. Of the number of allowable and non C
"set_zoom_speed"
"set_zoom_rel"
"set_zoom"

"wait_click"
"is_key"

"wheel_right"
"wheel_left"

"@ title"
"@ param"
"@ default"

"set_user_tv96"
"set_zoom_speed"
"set_zoom_rel"
"set_zoom"

"wait_click"
"is_key"

"wheel_right"
"wheel_left"

"@ title"
"@ param"
"@ default"

"md_detect_motion" commands detector movement. Questions to the MX3 ?
"md_get_cell_diff"

"get_autostart" parameter checking autostart for scripts
"set_autostart" Setting this option to autostart scripts
With these commands should be cautious. Specified Autorun leads to the script when you turn a camera on. Authorship - fingalo

"get_usb_power, checking for USB connectivity. Works for series A and S-as a minimum. For G-series is not working. Integration with USB- button. Authorship - EWAVR
"exit_alt"

"end"


"
!!! Łączenie podwójnego wpisu !!!
jakby ktoś znał angielski-niech przetłumaczy te nowe funkcje

nie wszystko niestety kumam ja i część widowni

ale wersja wyszła PORAŻAJĄCA trzeba przyznać
to nwe forum CHDK było świetnym pomysłem
po otwarciu nastapiła wręcz eksplozja nowych świetnych pomysłów-i do tego w dużej mierze już zrealizowanych

[dikamilo]

shutter speed value - ustawienia czasu naświetlania

Pozwala na ustawienie max 100 sekund i minumum 1/10000. Ustawienie odbywa się na mnożeniu 2 wartość, (Override shutter speed * valve factor).

Override ISO value - ustawienia ISO

Pozwala na zmiane iso do niestandardowych opcji od ISO 1 do XX testowałem ISO 50 na moim A630 ale nie zauważyłem żadnej różnicy pomiędzy ISO 50 a 80.

Override subject dist.value - ustawienia odległości fokusa

W zakładce OSD parameters można włączyć wyświetlanie "niestandardowych" ustawien na wyświetlaczu.

[gg123456]

shutter speed value - ustawienia czasu naświetlania

Pozwala na ustawienie max 100 sekund i minumum 1/10000. Ustawienie odbywa się na mnożeniu 2 wartość, (Override shutter speed * valve factor).

Ja to chce, ja to chce! Tylko kto mi zrobi CHDK do A300?

[Kociałko]

jeśli chodzi o max czas otwarcia migawki -da sie w nowym fimwarze CHDK ustawić niby 100 sekund ale chłopki na forum twierdzą ,że i tak max dla Canonków to 65 sekund

"Value factor (mm)" - funkcja ,która pozwala w trybie Manual focus -ręcznego ustawiania ostrości --ustawić w zakresie 1mm-500mm ostrość (i zapamiętać ją ?) niezależnie od ustawień ręcznych ostrości

"Subj.distance bracket.value (MF)," -to prawdopodobnie braketing ostrości przydatny przy makrofotografii gdy głębia ostrości jest mała-robimy serię zdjęć z ostrością ustawioną w różnych punktach i łączymy programem (coś jak zabawa z HDR) http://www.heliconsoft.com/heliconfocus.html


"Miscellaneous Values"/
"Show 'real' Aperture,"-pokaż prawdziwą wartość przesłony
"Show 'real' ISO-show"-pokaż PRAWDZIWĄ wartość ISO (na ekranie pojawia się jako I-R)
"Show 'market' ISO-show"-pokaż ISO marketingowe jak ustawia Canon (pokazuje się jako wartość I-M)
"Show ISO only in Autoiso mode"-pokaż ISO na ekranie w trybach HI oraz AUTOISO

ktoś rozgryzł jeszcze coś????