Strona 2 z 2 PierwszyPierwszy 12
Pokaż wyniki od 11 do 12 z 12

Wątek: Canon 1Ds Mk 2 wiesza się przysłona.

  1. #11
    Pełne uzależnienie
    Dołączył
    Mar 2012
    Miasto
    Posty
    1 254

    Domyślnie Odp: Canon 1Ds Mk 2 wiesza się przysłona.

    Cytat Zamieszczone przez AndrzejXM Zobacz posta
    albo co jest mozliwe ale nie jestem pewien czy ten model moze to miec - czujnik zalozenia czes na bagnet. Jakis maly "pipek" gdzies dookola bagnetu albo pod nim / w nim. Gdy nakrecasz cokolwiek na bagnet aparat spodzeiwa sie obiektywu (komunikacji z nim) a tego nie ma.
    Bingo, trafiony zatopiony.

    The lens detection Microswitch

    On some EOS bodies there is a small microswitch in the lensmount which must not be tripped by any attached lens or lens adapter in order for the camera body to work. If an adapted manual focus lens trips this microswitch, the camera body them looks for a valid EF series lens to be attached. If it doesn't see the correct electrical connection the the camera body thinks there is an error condition and will not operate. I've never been able to find an official list of which bodies have this switch and which don't. The early 1D series bodies do, up to the 1D MkII. The 1D MkIII doesn't. I think the D30, D60 and 10D have it too (note that's the D30/D60 not the later 30D/60D). Some, possibly all, EOS film bodies have it. I know the EOS-3 does for example.

    If you have one of the bodies with this microswitch and your adapted lens causes the camera to freeze you have to remove a small part of one of the bayonet flanges in order to avoid tripping the switch. Either that or do not lock the adapter completely in the EOS mount. If you don't fully rotate it so that it "clicks" into place it won't trip the switch. Of course the adapter is them not fully locked onto the camera, so you need to be careful not to accidentally allow the lens to part company with the camera!
    Źródło: http://www.bobatkins.com/photography...focus_EOS.html

    Co z tym fantem zrobić?

    https://photography-on-the.net/forum...d.php?t=906129

    https://www.photo.net/discuss/thread...m-lens.475414/

    http://photography-on-the.net/forum/...postcount=4460
    off to find the dremel, will report back later
    All fixed! Grinded about 3mm off the mount, works perfectly now Turns out I was pretty close to what was happening with my second message!
    If you look at the 10oclock position to the camera body, you will see a black pin. When this is depressed it tells the camera that there is a lens mounted to the body. The camera then looks for the electronic contacts, which it can't find. So it gets confused and won't fire.
    By removing the bit of the lens mount that contacts this pin, you solve the problem
    Jeśli dobrze rozumiem wystarczy zeszlifować kilka milimetrów z jednego z tych rygli bagnetu?

  2. #12

    Domyślnie Odp: Canon 1Ds Mk 2 wiesza się przysłona.

    Na to wychodzi... Po partyzancku mozna nie dokrecac przejsciowki do konca. Tylko czy bedzie sie pewnie trzymac?
    Ostatnio edytowane przez AndrzejXM ; 09-11-2018 o 13:35
    Mały, prosty, fajny 100D. https://www.flickr.com/photos/andrzejxm/

Strona 2 z 2 PierwszyPierwszy 12

Uprawnienia umieszczania postów

  • Nie możesz zakładać nowych tematów
  • Nie możesz pisać wiadomości
  • Nie możesz dodawać załączników
  • Nie możesz edytować swoich postów
  •